One, to learn, take an active part in agricultural machinery parts of the micro tillage machine training before use
       One is the manipulation and maintenance technical training, the second is for the agricultural service management skills training. Such as the use of diesel engine, rotary tillage tool selection, transfer, cultivation technique, field maintenance has a lot of place to study. Training well, tractor driver control technology, the better, maintain well, the machine's performance is better, its fuel, the operation quality, economic benefits is the better. For an example of the simplest starting the machine, not to participate in training, some tractor driver didn't grasp the technical main point, the starting method of micro tillage machine is not correct, is very difficult, and often damage to start pulling plate, spring and pull on the rope. As another example, some of the machinist. Nowadays, there is no follow after the first difficult, first cultivated upland field of launching general control order again, to get the new machine hand was under paddy cultivation, the result is that such as plant water, card file, trapped in the fields, such as not to many man-made fault. But there are a group of skilled machinist, manipulation of their micro tillage machine bought in 2005 and 2006, due to the maintenance of good, correct manipulation methods, machine so far hasn't been any big trouble, every assignment in more than 150 mu, cultivation quality, the farmer very highly.
      Second, the machine must adhere to in first, after use
      New micro tillage machine and after overhaul of micro tillage machine must be properly adjust, can play a proper comprehensive efficiency. New machine in terms of the correct method is: the first step, to the engine and the engine idling, respectively in low speed, medium speed and high speed running again, a total of about five hours; Running-in, the second step, with 50% of the load is generally find relatively soft land for rotary tillage operation, about 15 hours. The third step, replace the engine oil, wait for after completion of the above two steps, strike off the oil inside the engine, replenish ourselves in line with the brand of the right amount of new oil. The fourth step, check each operating mechanism of the adjusting valve clearance and other work schedule, tighten loose screws, etc. Replacing the connecting rod assembly, such as crankshaft, connecting rod, small watts, piston, piston ring, etc.) of the engine will not put into the running-in before normal use.

       Three, to always maintain a "clean"
       (a) fuel cleaning: in tongjiang, be sure to use standard of 0 # diesel oil, had better use the larger iron drum to regular gas station to buy oil, precipitation 48 hours before using, insist on a fuel tank cleaning every month, every six months) after 500 hours (or use in a fuel filter;
(2) the lubricating oil cleaning: diesel engine and walking speed change box USES magnitude of cc diesel engine oil, engine oil barrel must be used, in 20 hours after an oil change for the first time, later every work 100 hours in the oil, every time before starting to check whether the oil quantity is enough, not enough to make up, too much also want to put off some (or overheat and blue smoke), after every work 100 hours after washing the oil filter. Walking speed change gear oil, is strictly prohibited in the inside of the oil after the half load work 8 hours in time, change again after full load working 20 hours once, after every work 150 hours, change;
(3) the combustion air cleaning: always check and clean fuel filter, air filter oil box must maintain a moderate amount of oil, the oil box and damage should be replaced as soon as possible a new bubble, or after a long time will cause rapid wear of valve, piston, piston ring and cylinder.
        Four, to calm in the face of the four types of accidents
        (1) is the field move not careful will lead to micro tillage machine, encounter this kind of circumstance should immediately stop, if caused by damage of operating mechanism of engine can't stop, can immediately according to the decompression lever parking (this method only promised to engine can't normal downtime or diesel engine speed is used in emergencies such as);
(2) new machinist plow paddy field using reverse improper manipulation, easily cause micro tillage machine plant water (i.e. on the nose, by air filter mud sucked into the cylinder), to stop the machine immediately to check at this moment, can no longer continue to use (or engine is likely to cause severe damage), and get in touch with 3 packets of pits as soon as possible;
(3) is a machine with sound when it is necessary to stop the machine immediately to check, and shall report malfunctions 3 packets of pits; (4) is a machine has small failure to deal with as soon as possible, otherwise "minor medical, eventually into a great misfortune. Note: on the clean up the rotary tillage tool winding weeds or other small failure, must first after downtime implementation; When winter low temperature starting diesel engine is bad, can change in line with the brand of small oil viscosity, it is forbidden to use inlet starting ignition way.
         Five, to grasp the correct phase micro tillage machine in the park
         Micro tillage machine using seasonal is strong, in the period of park often for more than six months, if improper parking method, also can damage (such as: valve closes lax will cause the valve and cylinder liner rust, etc.). Need long-term parking micro tillage machine, in the final after use, to strike out the old engine oil, diesel engine injection into the new oil, remove the oil plug on the cylinder head cover, add about 2 ml of oil, press the decompression starting handle don't loosen, pull the recoil starter rope 5-6 times (generally do not need to start diesel engine), then loosen the decompression handle, slowly pull the starter rope, until feel a greater resistance. Release the diesel fuel tank of diesel oil (a little). Then let out walking speed change box of oil, note into the new oil, finally clear the oil on the micro tillage machine and cutting tool, soil and weeds, etc., keep the machine in drafty dry and will not be weathered.